NATE ITEM 963C

5000 GALLON TYPE IV

Model Profile

2574  6 X 4


 

DIMENSION:

Wheelbase 252" Cab to Axle 174" Axle to Frame 53"

ENGINE, DIESEL:

{Caterpillar C-10} 50 State, 305 HP @ 2100 RPM, 1150 lb-ft Torque @ 1200 RPM, 2100 RPM Governed Speed, 320 Maximum HP and With Electronic Controls

TRANSMISSION, MANUAL:

{Fuller RTLO (F)-12913A} 13-Speed Manual; With Double Overdrive and With Air Shift

CLUTCH:

{Eaton Fuller EP1552} Easy-Pedal Plus, Two-Plate, Cast Angle Spring; Ceramic, 15.5" Diameter, Soft Clutch 7-Spring Damper, Mechanical Pull-Type Control, With Kwik-Adjust (Manual) Feature, 1700 lb-ft Torque Capacity

AXLE, FRONT, I-BEAM TYPE:

{International I-160s} 16,000-lb Capacity

AXLE, REAR, TANDEM:

{Meritor (Rockwell) RT-52-185} Single Reduction 52,000-lb Capacity With Lube Pump and "R" Wheel Ends Gear Ratio: 4.56

CAB:

Conventional, Steel, 80" Wide

TIRE, FRONT:

(2) 315/80R22.5 UNISTEEL G291 (GOODYEAR) 491 rev/mile, load range J, 18 ply

TIRE, REAR:

(8) 11R22.5 UNISTEEL G159 (GOODYEAR) 501 rev/mile, load range G, 14 ply


BODY SPECIFICATIONS



TANK:

5,000 U.S. gallons, alluminum alloy, fully baffled, overturn protection, vapor recovery ready, 20" manhole with venting, full length subframe, hardwood sills, capacity marker, bottom loading capability (API and D-1 adapters), level sensor controlled shut-off for bottom loading, automatic flow control valve with emergency controls, DOT 406 compliance.

SKIRTING (OPTIONAL) AND CABINETS:

14 gauge mild steel construction, full length both sides, bolt on construction, hose tubes (4) for 10' drop hoses, 16 gauge mild steel doors with stainless steel hinges, bar grating cabinet floor, cabinet lights, fire extinguisher niches.

PLUMBING SYSTEM:

Centrifugal pump with mechanical seal, 200 GPM rating, PTO control in cab, 40 mesh inlet strainer, flow meter with temperature compensator, reset counter and totalizer, manual rewind hose reel with 50' of 2" noncollapsible hose, flow control and bypass valves, deadman control, control panel with gauges, aluminum piping with grooved type couplings, suction stub with 3" manual valve (also uses for nonmetered gravity discharge), 4 optional 2 1/2" x 10' suction hoses, optional speed ends for de-drumming and defueling, ground cable and reel, API 1581 Group II, Class C filter separator with water slug control and air eliminator, fuel sampling fitting, fuel quality monitor, overwing closes circuit and underwing (D-1) nozzles with dry break couplings, emergency dry break, self-loading and recirculation capabilities.

MISCELLANEOUS:

:Brake interlocks for bottom loading and discharge operations, vaporproof lighting, fuel load chart, operating instruction and schematic diagram plates. Electromagnetic radiation suppression in accordance with SAE J551 limits, tubular steel (ASTM A500, Grade B) rear bumper per DOT 406, tool storage in cab.

CAB & CHASSIS SPECIFICATIONS



BASE CHASSIS:

Model 2574 6x4 with 252" Wheelbase, 174" Cab to Axle and 53" Axle to frame

TOW HOOK, FRONT:

(2) Frame Mounted

FRAME RAILS:

Heat Treated Alloy Steel (110,000 PSI Yield); 10.125" x 3.502" x 0.312"; 229" thru 252" WB with 92" Maximum AF

FRAME REINFORCEMENT:

Outer "C" Channel, Heat Treated Alloy Steel (110,000 PSI Yield) 10.813" x 3.812" x 0.312", 229" thru 252" WB with 92" Maximum AF.

BUMPER, FRONT:

Steel, Swept Back

AXLE, FRONT, I-BEAM TYPE:

{International I-160S} 16,000-lb Capacity; Less Shock Absorbers

INCL:

  • SPRING PINS 1.25" Diameter Smooth Pin with Annural Lube Groove

BRAKE SYSTEM, AIR:

Dual System for Straight Truck Applications

INCL:

  • BRAKE CHAMBERS, SPRING (4) Rear Parking
  • DUST SHIELDS, FRONT BRAKE
  • DUST SHIELDS, REAR BRAKE
  • BRAKE LINES Color Coded Nylon
  • SLACK ADJUSTERS, FRONT Automatic
  • SLACK ADJUSTERS, REAR Automatic
  • DRAIN VALVE Twist-Type
  • INVERSION VALVE and Double Check Valve

BRAKES, FRONT:

AIR CAM S-Cam; 16.5" x 6.0"; Includes 20 Sq. In. Brake Chambers

BRAKES, REAR:

AIR CAM S-Cam; 16.5" X 7.0"; Includes 30 Sq. In. MGM Spring Actuated Parking Brake Chambers

BRAKES SHOES, REAR:

Cast

AIR BRAKE ABS:

{Bendix AntiLock Brake System} Full Vehicle Wheel Control System (4-Channel)

AIR DRYER:

{Bendix AD-9} With Heater, Standard Location

AIR COMPRESSOR:

{Bendix Tu-Flo 550} 13.2 CFM

AXLE, REAR, IDENTIFIER FOR ABS:

{Meritor (Rockwell)}

STEERING COLUMN:

Stationary

STEERING WHEEL:

2-Spoke, Black; 18" Diameter

STEERING GEAR:

(2){Sheppard M-90/M-80}Duel Power

EXHAUST SYSTEM:

Single, Horizontal Muffler, Vertical Tail Pipe Aluminized Steel; Includes Tail Pipe Guard; Grab Handle; Frame Mounted Right Side

ELECTRICAL SYSTEM:

12 - Volt, Standard Equipment

INCL:

  • TURN SIGNAL FLASHER
  • TURN SIGNAL SWITCH Self-Cancelling with Integral Hazard Switch
  • HEADLIGHT DIMMER SWITCH Integral with Turn Signal Switch
  • FUSES, ELECTRICAL SAE Blade-Type
  • HEADLIGHTS (2) Sealed Beam, 7" Round
  • HORN, ELECTRIC Single
  • PARKING LIGHT Integral with Front Turn Signal and Rear Tail Light
  • STOP, TURN, TAIL & B/U LIGHTS Dual, Rear, Combination with Reflector
  • STARTER SWITCH Electric Key Operated
  • TURN SIGNALS, FRONT Fender Mounted with Integral Reflectors, Marker Lights and Auxiliary Side Turn Signals
  • WIRING, CHASSIS Color Coded and Continuously Numbered
  • WINDSHIELD WIPERS Single motor, Electric, Cowl Mounted
  • WINDSHIELD WIPER SWITCH 2-Speed Integral with Turn Signal Swith with Wash and Mist Wipe and Intermittent Feature

CIGAR LIGHTER:

HORN, AIR:

(2) {Grover} Chrome; with Single Pedestal Mounting

STARTING MOTOR:

{Delco-Remy America MT-42 Type 450} 12-Volt With Thermal Over-Crank Protection

ALTERNATOR:

{Delco-Remy America 22-SI} 12-Volt 130 Amp. Capacity

BATTERY SYSTEM:

{Fleetrite} Maintenance-Free (4) 12-Volt 2600CCA Total

RADIO:

{Panasonic CRW200B} AM/FM Stereo, With Weather Band; 4 Channel At 15 Watts Each, With Electronic Tuning and Clock, Includes Multiple Dual-Cone Speakers

INCL:

  • SPEAKERS IN CAB (2) Dual-Cone

JUMP START STUD:

Remote Mounted

RUNNING LIGHT:

(2) Daytime

FRONT END:

Tilting, Fiberglass

INCL:

  • MUD FLAPS, FRONT WHEELS (2)
  • GRILLE Bright Finish Anodized Aluminum

PAINT SCHEMATIC:

PT-1 Single Color, Design 100

INCL:

  • PAINT SCHEMATIC ID LETTERS "AJ"

PAINT TYPE:

Base Coat/Clear Coat, 1-2 Tone

CLUTCH:

{Eaton Fuller EP1552} Easy-Pedal Plus, Two-Plate, Cast Angle Spring; Ceramic, 15.5" Diameter, Soft Clutch 7-Spring Damper, Mechanical Pull-Type Control, With Kwik-Adjust (Manual) Feature, 1700 lb-ft Torque Capacity

INCL:

  • CLUTCH RELEASE BEARING Greasable

RADIATOR HOSES:

Silicone; Non-Molded

COLD STARTING EQUIPMENT:

Ether, with Electric Cab Control

ENGINE, DIESEL:

{Caterpillar C-10} 50 State, 305 HP @ 2100 RPM, 1150 lb-ft Torque @ 1200 RPM, 2100 RPM Governed Speed, 320 Maximum HP and With Electronic Controls

INCL:

  • WATER FILTER Remote Mounted
  • STARTING MOTOR 42MT
  • GAUGE, AIR CLEANER RESTRICTION Air Cleaner Mounted
  • AIR CLEANER with Vacuator
  • CRUISE CONTROL Electronic
  • ENGINE SHUTDOWN Electric, Key Operated
  • GOVERNOR Electronic
  • THROTTLE, HAND CONTROL Electronic, Instrument Panel Mounted
  • ENGINE OIL DRAIN PLUG Magnetic
  • OIL FILTER, ENGINE Spin-On Type
  • TIMER Idle Shutdown
  • FUEL FITLER Engine Mounted

FAN DRIVE:

{Horton Model HTS} Automatic On/Off Type Control; With Normally Closed Temperature Control;

INCL:

  • FAN Nylon

RADIATOR:

Cross Flow, Series System, 1150 Sq.In. Area and 1030 Sq.In. Charge Air Cooler

INCL:

  • ANTI-FREEZE -40F (-40C)
  • DEAERATION SYSTEM with Remote-Mounted Surge Tank and Sight Glass
  • RADIATOR HOSES Premium, Rubber

HOSE CLAMPS, RADIATOR HOSES:

{R.G. Ray Mini Flex Seal} Coil Spring/ "T"-Bolt Type, for Radiator Hoses over 1"I.D.

TRANSMISSION, MANUAL:

{Fuller RTLO (F)-12913A} 13-Speed Manual; With Double Overdrive and With Air Shift

INCL:

  • CLUTCH BRAKE Torque Limiting
  • FILL PLUG, MAGNETIC

AXLE, REAR, TANDEM:

{Meritor (Rockwell) RT-52-185} Single reduction 52,000-lb Capacity With Lube Pump and "R" Wheel Ends Gear Ratio: 4.56

SUSPENSION, REAR, TANDEM:

{Hendrickson RT2-520} Walking Beam Type 54" Axle Spacing; 52,000-lb Capacity With Bronze Center Bushings

FUEL TANK:

Top Draw; Rectangular Steel, 88 U.S. Gal., 333 L Capacity With Center Step. Mounted Left Side, Under Cab

INCL:

  • FUEL TANK HOSE Crimped End

CAB:

Conventional, Steel, 80" Wide

INCL:

  • ARM REST (2) Molded Plastic, Charcoal; One Each Door
  • FLOOR COVERING Rubber, Black
  • INTERIOR SHEET METAL Painted, Color Based on the Window Ledge Color of the Exterior
  • CONSOLE, OVERHEAD Molded Plastic with Dual Storage Pockets and Retainer Nets and CB Radio Pocket with Cover; Pearl gray with Black Pockets
  • COAT HANGER Located in Cab
  • ASH TRAY Instrument Panel Mounted
  • CLEARANCE / MARKER LIGHTS (5) Flush Mounted

GLASS, ALL WINDOWS:

Tinted

COLOR, INTERIOR:

Quartz Brown

MIRRORS:

(2) Rectangular, West Coast Type, 16" x 7" Size with 102" Wide Spacing, Painted Head and Painted Steel Brackets

GAUGE CLUSTER:

English with English Electronic Speedometer and with Tachometer for Air Brake Chassis

INCL:

  • GAUGE, ENGINE OIL PRESSURE Electronic
  • GAUGE, WATER TEMPERATURE Electronic
  • VOLTMETER
  • GAUGE, AIR PRESSURE Dual

SEAT, DRIVER:

{International} Non-Suspension, Low Back, Vinyl With Printed Vinyl Insert, Folding Back With Storage Pocket

INCL:

  • SEAT BELT 3-Point, Lap and Shoulder Belt Type

SEAT, PASSENGER:

{International} Non Suspension, Low Back, Vinyl, Folding Back With Storage Pocket

INCL:

  • SEAT BELT 3-Point, Lap and Shoulder Belt Type

AIR CONDITIONER:

{International Blend-Air} With Integral Heater & Defroster

INCL:

  • HEATER HOSES Premium
  • REFRIGERANT Hydrofluorocarbon HFC-134A

MIRROR, CONVEX:

(2) Stainless Steel, 8" Diameter, Mounted Below Primary Mirrors

CAB INTERIOR TRIM:

Vocational

INCL:

  • STORAGE POCKET, DOOR Metal, Charcoal, Full-Length; Driver Door
  • "A" PILLAR COVER Molded Plastic, Pearl Gray
  • HEADLINER Vinyl
  • INSTRUMENT PANEL TRIM Molded Plastic, Pearl Gray Upper, Black Lower with Cup Holder Molded into the Upper Area of the Instrument Panel Cover
  • DOME LIGHT, CAB Rectangular Center Mounted with Integral Swiveling Map Light, Door Activated
  • SUN VISOR (2) Padded Vinyl with Toll Ticket Strap
  • CAB INTERIOR TRIM PANELS Vinyl, Half-Height
  • DOOR TRIM PANELS Painted Metal

ACCESS, CAB:

Driver & Passenger Sides

INCL:

  • GRAB HANDLE, CAB INTERIOR (1) "A" Pillar Mounted, Passenger Side
  • STEP (4) Two on Each Side
  • GRAB HANDLE (2) Exterior, "B" Pillar Mounted, One Each Side

WHEELS FRONT:

DISC; 22.5" Painted Steel, 10-Stud (285.77MMBC) Hub Piloted, Flanged Nut, Metric Mount, 9.00 DC Rims; with Steel Hubs

INCL:

  • WHEEL SEALS, FRONT {International} Oil Lubricated Wheel Bearings
  • PAINT IDENTITY, FRONT WHEELS White

WHEELS, REAR DUAL DISC:

22.5" Painted Steel, 10-Stud (285.75MM BC) Hub Piloted, Flanged Nut, Metric Mount, 8.25 DC Rims; With Steel Hubs

INCL:

  • PAINT IDENTITY, REAR WHEELS White
  • WHEEL SEALS, REAR Oil Lubricated, Includes Wheel Bearings

WHEEL SEALS, FRONT:

{International} Oil-Lubricated Wheel Bearings

TIRE, FRONT:

(2) 315/80R22.5 UNISTEEL G291 (GOODYEAR) 491 rev/mile, load range J, 18 ply

TIRE, REAR:

(8) 11R22.5 UNISTEEL G159 (GOODYEAR) 501 rev/mile, load range G, 14 ply